Operating principle of ammeters and voltmeters:

20 Apr

Operating principle of ammeters and voltmeters:

Introduction:

Ammeter

Ammeter

 

 

Voltmeter

Voltmeter

In our day today life, many times we require to measure different electrical quantities like current, voltage, resistance, etc. While doing experiment, there is necessity of multimeter. As we have already discussed about multimeter, how it measures different electrical quantities like electrical current, voltage, resistance, etc. But the basic instruments for the measurement of electric current and voltage are ammeters and voltmeters respectively.

Let us discuss these instruments one by one, operating principle (working principle) of ammeters and voltmeters, finally major differences between ammeters and voltmeters.

Operating Principle:

Analog ammeters and voltmeters are classed together as there are no fundamental differences in their operating principles. The action of all ammeters and voltmeters, with the exception of electrostatic type of instruments, depends upon a deflecting torque produced by an electric current .in an ammeter this torque is produced by a current to be measured or by a fraction of it. In a voltmeter this torque is produced by a current which is proportional to the voltage to be measured. Thus all analog voltmeters and ammeters are essentially current measuring devices.

The essential requirement of measuring instruments are (i) that its introduction into the circuit, where measurements are to be made, does not alter the circuit conditions ;(ii)the power consumed by them for their operation is small.

Ammeters:

Ammeters are connected in the series with the circuit whose current is to be measured. The power loss in an ammeter is (I^2.Ra) where I is the current to be measured Ra is the resistance of the ammeter therefore ammeter should have low electrical resistance so that they cause a small voltage drop and consequently absorb small power.

Voltmeters:

Voltmeters are connected in parallel with the circuit whose voltage is to be measured .the power loss in voltmeter is (V^2/Rv), where V is the voltage to be measured and Rv is the resistance of the voltmeter. Therefore voltmeters should have a high electrical resistance, in order that the current drawn by them is small and consequently the power consumed is small.

Difference between Ammeters and voltmeters:

 Parameters

Ammeter

Voltmeter

Connection It is to be connected in series mode It is to be connected in parallel mode
Resistance It has comparatively low resistance It has high resistance
Uses It is used to find the amount of current flowing in the circuit It is used to find the potential difference in the circuit
Circuit Circuit must be disconnected in order to attach the ammeter Circuit does not need to be disconnected
Accuracy Considered as less accurate Considered as more accurate compared to ammeter
About these ads

4 Responses to “Operating principle of ammeters and voltmeters:”

Trackbacks/Pingbacks

  1. Effect of temperature changes on Ammeter | MyClassBook - December 11, 2013

    […] due to temperature changes in ammeters can be eliminated by using the same material for both shunt and moving coil and kept at the same […]

    Like this

  2. Single beam filter photometer | MyClassBook - December 29, 2013

    […] It consists of a source of light (tungsten filament lamp), lens to make the light beam parallel, filter of wavelength selection, cuvette with sample holder for keeping the solution to be analyzed , detector (photocell) and reading device (galvanometer or micro-ammeter). […]

    Like this

  3. Digital Voltmeter using 8051 microcontroller – Mini-Project | MyClassBook - January 27, 2014

    […] are two types of voltmeter as analog voltmeter and digital voltmeter. Analog voltmeter moves pointer on a scale but it has some limitations like accuracy of few percent […]

    Like this

  4. Brief theory about WAVE ANALYZER | MyClassBook - January 30, 2014

    […] versus frequency. It has an operating range of about 0.02 Hz-250 GHz. A wave analyzer is a voltmeter which can be accurately tuned to measure the amplitude of a single frequency, within a band of […]

    Like this

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

Follow

Get every new post delivered to your Inbox.

Join 214 other followers

%d bloggers like this: